Bedding Plastic Rifle Stocks

A customer of well-known gunsmith (and Hall-of-Fame shooter) Thomas Speedy Gonzalez recently asked Speedy about bedding compounds. Speedy offered some interesting advice based on long-term testing of various materials. Speedy favors Marine-Tex because it is very stable over time, while other materials can shrink up to 6% dimensionally. I've used the drill a whole bunch of holes (~3/16" holes x 3/16" deep) in plastic stocks and haven't noticed any movement or looseness in the bedding material. If the stock is a flexi-flyer like a lot of these moulded plastic stocks are it could be a bear.

Premium 1/2Inch Extra Thick Exercise Printed Yoga Mat

Rifle bedding is fundamental to rifle accuracy. The term bedding refers to the fit and stability of a barreled action within the rifle stock. If the fit and stability of the metal work in relationship to the stock is poor, the rifle will be in-accurate. Bedding a rifle with epoxy resin is the optimum method of obtaining a correct fit, long term.

Bedding plastic rifle stocks. If a gun has a bedding block—a reinforced area around the recoil lug—that’s a good sign. Bedding blocks are a good practice, especially on heavy-recoiling rifles. Bedding blocks spread the recoil out and reduce the punishment that the recoil lug area is subjected to. In plastic stocks, I like built-in metal bedding bases. The problem with most factory synthetic stocks (injection molded plastic) is the forend flexes a lot and can interfere with the barrel. Prep for bedding a factory synthetic stock takes more time than for wood and attention to detail is real important. I'm considering bedding a M-700 and have researched the google quite a bit. I realize about any of the big name gun places sell kits. However Can it be done just as good from supplies from the local hardware store. One place I read someone said they used a two part epoxy plastic sheet bond, while another said they had good results with JB-Weld.

I hate to tell you guys but if your looking to do any serious accuracy work, throw away the tupperware stocks. Don't waste your time trying to make them stiffer or pillar bed them. It's a pain just to get the bedding to stick (too much oil in the plastic). At the least go with the Bell and Carlson stock it's deffinately a step in the right. Pillar bedding is common in wood, fiberglass and plastic rifle stocks. In addition to helping the rifle maintain accuracy, the pillars provide consistent spacing between the action and bottom metal which is necessary with modern detachable magazine systems. Bedding pillars are found in different materials and thicknesses. To “bed” a rifle means to precisely fit the stock around the action (and sometimes the barrel, too). Two-piece stocks mount onto the firearm, rather than supporting the firearm as one-piece stocks do, so bedding is generally only useful (or possible) with one-piece stocks. The purpose of bedding is to tighten the imperfect fit between stock and action, which would otherwise allow the.

If it says Devcon Plastic Steel Putty and mixes 2.5:1 by volume or 9:1 by weight then it's the same stuff. If it mixes 1:1 and/or does not say Devcon Plastic Steel Putty then you've got a different Devcon product. Note that they also make a Plastic Steel Epoxy that comes in tubes - that is a different item. The V-block system, which was developed by H-S Precision for the Army’s M24 sniper rifle, consists of a hardened aluminum bedding chassis permanently molded into the company’s hand-laid Kevlar/graphite-reinforced fiberglass stocks. However, the plastic stocks that are so popular today need to be roughed up to give the bedding compound something to adhere to as the bedding does not stick well to plastic stocks. I often drill small holes that angle away from the action to allow the compound to get into the holes and keep the compound in place.

Typical injection molded stock for a bolt action rifle. Photo by Jim Clary. First off, I am not talking about the high quality synthetic/composite stocks produced by manufacturers like McMillan. I am referring to those lightweight, injection molded plastic stocks sold by virtually every major firearms manufacturer in the United States. bedding plastic rifle stocks, bedding plastic stocks, bedding savage plastic stock, modifications to savage plastic rifle stocks, plastic rifle stocks, plastic stocks mail. Click on a term to search for related topics. Thread Tools: Show Printable Version. Email this Page. Display Modes: Linear Mode. I generally use about a 1- to 1.5-inch-diameter pad of bedding per spot. Once the bedding is in place, put the barreled action back in the stock and tighten the action screws as you would normally. Allow the bedding to fully cure and then disassemble the rifle. The bedding in the barrel channel will have formed two distinct support pads.

Does anyone have experience glass bedding molded plastic stocks? I bought a Howa mini action .223. The factory stock is pillar bedded, but there is enough slop side to side that depending on where things are when the screws are tightened, the barrel can contact the stock. MatchGrade Stock stabilizer removes plastic stock flexing! MatchGrade Synthetic stock stabilizer is an easy to use product, designed by Terminal Ballistics Research to remove flexing from plastic rifle stocks. Used in conjunction with MatchGrade bedding compound, MatchGrade Stock Stabilizer creates a rigid forend and optimizes rifle accuracy. Bedding a rifle increases accuracy by creating a precise fit between the stock and the action. This precise fit eliminates stress in the action and provides a solid foundation for an accurate rifle.. Placing some blue tape on a plastic bench block, I use a barrel cut-off to guide my razor.. In some stocks, the sides of the lugs do not.

Block bedding is a very effective way to accurize the newer factory synthetic stocks that have internally structured compartments in the forend and around the action area. Block bedding basically involves surrounding the recoil lug with a block of steel. You'll bed the rifle at four points: recoil lug, back of tang, around the two guard screws. Before bedding your rifle—coating the stock’s interior with an epoxy resin—complete a dry run. Make sure all of the pieces fit together properly before applying the bedding material. Insert the action, followed by the trigger, magazine box, bolt, and bolt release.

Online Shopping Bedding, Furniture, Electronics, Jewelry